Join us at SMM Exhibition 2024 in Hamburg from 3th to 6st of september

Hawke Sealing Solutions

For Civil use

For civil use, our transit systems feature essential elements including frames, blocks, compression systems, accessories, and installation tools. Ensure the integrity of your fire-rated bulkheads, decks, walls, or enclosures where cables or pipes pass.

Product advantages

HCX

Standard Civil Flanged frame to be bolted or casted to a wall or floor.

HCOX

Frame with removable end which allows the frame to be installed around existing cables and pipes.

HCLX

Civil large frame for sealing services with an overall diameter in excess of 100mm.

HCLOX

This civil frame allows to seal services with a medium radius, greater than 100mm when the cables and pipes are already installed.

Sleeve CBO

Sleeve with flange and removable end which allows installation around existing cables.

Designed to be bolted or casted
Materials: Mild Steel, Stainless Steel and Aluminium
To be sealed with standard or EMC HRT/HRTO and HRST

Sleeve CB

Sleeve with flange for Hawke Round Transits.

Designed to be bolted or casted
Materials: Mild Steel, Stainless Steel and Aluminium
To be sealed with standard or EMC HRT/HRTO and HRST

Sleeve CBC

Sleeve with flange for Hawke Round Transits.

Designed to be casted
Materials: Mild Steel, Stainless Steel and Aluminium
To be sealed with standard or EMC HRT/HRTO and HRST

HRST

Hawke HRST is a round sealing solution for a single/pipe passing through a wall or bulkhead/deck. Each size of HRST frame can seal a large range of diameters without any onsite modifications.

HRTO

Hawke HRTO Certified for both Civil and Marine applications.The HRTO has been designed to be sealed using standard Hawke tolerant blocks, Hawke HRTO provide effectively sealing of cables and pipes through a circular aperture.

Hawke HRTO is supplied as an OPEN frame, so that it can be installed after laying the cables or pipes.

Duct Seal

Hawke Duct Seal is a sealing system for cables passing through ducts or pipes, which ensures cabling is protected from water, smoke, corrosive chemicals, rodents and debris. Tried and tested in the field, Duct Seal is suitable for a wide range of cable including fibre optics, electrical wire, twisted pair or coax…

Its typical applications range from telecommunications to power distribution.

Hawke Standard Tolerant Blocks

The Hawke cable blocks have a tolarance that is achieved by having 5 points of contact with the cable that guarantees the sealing of the cable even if it is deformed.Thanks to this tolerance, each Hawke block covers a range of diameters between 3 and 4 mm. It is not necessary to manipulate the block, as this tolerance is achieved by deforming it when the system is compressed.

Hawke Blank Filler Blocks

Filler blocks are available in the same materials as the tolerant Blocks. They are used to fill spaces within the frame which are not required for services, thus allowing spare capacity for future requirements.

Hawke Wave Guides

Hawke manufacture a range of blocks to suit the most popular waveguides sizes. Hawke wave guide insert blocks are used inserted in Standard HF Blocks.

Hawke Trefoil Insert Blocks

Hawke Trefoil Insert Blocks: These blocks allow three single phase power cables to be sealed inside of the same cable block. *Available in 90mm and 120 mm size*

Hawke Special Insert Blocks

Civil Compression System

The Hawke compression system has 2 elements: The End Packer and the Compression Plate.

Unique steel insert pins on both sides of the Hawke Transit Compression System ensure that the correct level of compression is applied to each installation, without the need for special knowledge or decisions on the part of the installer.

Standard Stayplate

Stayplates ensure the blocks in a Hawke rectangular system (tolerant and blank ones) are fixed in position after compression.

High-pressure Stayplate

High-pressure Stayplates ensure the blocks in a Hawke rectangular system (tolerant and blank ones) are fixed in position after compression.

H-HC Frame

The H-HC frame is manufactured with a 5 cm flange. This flange can be placed centrally in the frame or offset on one side. Available in two sizes, 60 and 120 mm wide (internal).

Made of mild steel or stainless steel.
To be installed (bolted) inside or outside the panels and cabinets.
To be sealed with plugs and standard HAWKE compression system, stayplates and lubricant.
No additional tools required for installation.
Different sizes.

H-HC Compression System

The Hawke compression system has 2 elements: The End Packer and the Compression Plate.

Blank Filler blocks

Blocks designed to seal the cable clearances in the frame. This allows for the installation of new cables in the future within the same frame.

Hawke Standard Tolerant Blocks

Standard Stayplate 60mm

Stayplates ensure the blocks in a Hawke rectangular system (tolerant and blank ones) are fixed in position after compression.

H-DM Frame

Hawke H-DM is a low weight cable sealing solution, frames are made in aluminum to be installed (bolted) inside or outside the panelboards and electrical cabinets, designed for the sealing against external conditions.

Three different sizes.

Compression system (CSDM 120/S compression kit)

Hawke CSDM Compression system is used in H-DM frames to compress and seal the installation of cables and DM modules. It includes the endpacker unit, 5mm filler strip and two stayplates. The 5mm filler strip can be installed as either the top or bottom row of blocks within a H-DM aperture.

The extra 5mm strip is recommended to be placed on the bottom row of the frame, along with one of the stayplates.

DM Blank Filler Blocks

Blocks made of the same material as the standard blocks and designed to seal the free spaces of cables of the frame. This allows the installation of new cables in the future within the same framework.

Tolerant Blocks

Standard tolerant blocks for cable sealing between 15 mm and 60 mm. The H-DM system blocks have color coding to facilitate inspection and avoid installation mistakes.